sae 100r1at vs cat one-wire braid hose (716) working pressure* hose inner inner max. work. press. max. work. press. max. work. press. dash diameter diameter (psi) (bar) (kpa) size (in) (mm) 100r1 716 100r1 716 100r1 716-12 0.750 19.1 1250 1250 86 86 8600 8600-16 1.000 25.4 1000 1000 69 69 6900 6900-20 1.250 31.8 625 625 43 43 4300 4300

Fluid Flow Pressure Calculator. Enter your application's fluid properties, hose and coupling specifications, and our Fluid Flow Pressure Calculator will help identify your operational issues, so you can eliminate costly downtime, improve efficiency, and save money. ABOUT US. CUSTOMER SUPPORT. Company Overview.

3600. 3200. 1 - For higher pressures, see please contact Titan Fittings. 2 - Rating based on repeated pressure testing with a 4:1 design factor based upon hydraulic fluid leakage.

SAE J514 Working Pressure Ratings - Capable of 4-1 Minimum Burst SAE and NPT Fittings. Note: In the case of a fitting that is a jump size, it is recommend that the lower pressure of the two

Use our hydraulic hose size selection chart (nomograph) to choose the correct hose ID size, desired flow rate, and recommended flow velocity. 1300 111 247. Subscribe to our Newsletter; To find the bore size for a Pressure Line consistent with a Flow Rate of 100 litres per minute (26 US or 22 Imperial gallons per minute), and a Flow Velocity

If you work with hydraulics, make sure you have the right hose for A single fiber-braid hose typically has a lower pressure rating than 

From the tables below, the rated working pressure for the -4 male 37 degree tube end is 34.5 MPa (5,000 psi) and the rated working pressure of the -6 (3/8") male pipe end is 21 MPa (3,000 psi). The rated working pressure of the fining would be 21 MPa (3,000 psi). For proper performance, the design of any hydraulic system should take into

Below we've compiled a hydraulic hose fittings chart descri some of the more common fitting sizes and types currently in use by pipe fitters and other professionals. National Pipe Tapered Fuel (NPTF) National Pipe straight mechanical (NPSM) JIC 37° Flare (SAE J514) SAE 45° Flare (SAE J512) SAE Straight Thread O-ring (O-Ring Boss)

The hose has a 5,800 psi rating. Therefore the maximum pressure rating of the hose assembly would be 5,800 psi. Pressure ratings for each Parker end connection can be found on the Pressure Rating of Hose End Connections - PSI Chart in Section E. Pressure spikes can occur during machine operation in an instant.

To find the pressure rating for fittings, please see the Pressure Rating of Hose End Connectors chart. Fitting selection can be complicated 

Velocity range for intake line. Velocity range for pressure line. A Moving fluid. [ m/sec ]. A cross section [ cm2 ]. YOKOHAMA HYDRAULIC HOSE 5 

High-Pressure (psi range). Gates high-pressure hydraulic hoses meet a variety of governmental agency requirements and are offered in the following styles:.

10/15 · The hydraulic hose is made of synthetic rubber material, and also with steel wire reinforcement, so you can use the hydraulic hose pipe under high temperatures. And the typical rubber hydraulic hose is rated for the working operation to 212° F (100 ℃). And most hydraulic hoses offer a wide range of working temperatures.

Carbon Steel Fittings and Adapters · NPTF · NPSM · Flare Hydraulic · Flareless Compression.

Temperature range of -40ºC to 100ºC (-52ºF to 212ºF). Medium pressure hydraulic hose. The chart hereinunder displays the materials of seals most.

10/19 · Max. Operating Pressure: 375 to 1,500 psi. Min. Bend Radius: 3” to 10”. Usage: General use as a low-pressure hydraulic hose, including antifreeze and hydraulic oil. SAE

Constant Pressure Spiral Hose are designed to be easily identifiable by pressure rating for safe replacement. 5. NEW LOW TEMP HOSE RATED TO -70°F Key Products Arctic Hose High-pressure hydraulic hose used in construction, forestry, surface mining, oil and gas, waste handling, utilities and other applications where lower temperature can impact

The hydraulic hose is made of synthetic rubber material, and also with steel wire reinforcement, so you can use the hydraulic hose pipe under high temperatures. And the typical rubber hydraulic hose is rated for the working operation to 212° F (100 ℃). And most hydraulic hoses offer a wide range of working temperatures.

A nomograph is essentially a hose sizes chart. Consider your correct hose I.D., desired flow rate, and recommended flow velocity. If you know any of these two values, you can determine the third using the nomograph chart below. Pick your two known values. Lay a straight edge, intersecting those two values. Intersection on the third vertical

The chart below references nominal working pressure ratings for hydraulic steel tu classified as SAE J524, SAE J525, SAE J526 and SAE J356. These working pressures assume a 4:1 safety factor and have been calculated the standard formula P=S ( (D2-d2)/ (D2+d)). Please note the information provided is for reference only and should not be

5/14 · Typically, you see 1/4 in. as being a small hose. This one has a pressure rating of 3,250 psi. It’s important to consider that smaller diameter hoses, just by their nature, are able to resist higher pressures. The construction allows them to have less force across any given perpendicular surface.